How To Fix Internet Ping Spikes?

Internet ping spikes can be caused by issues with the WiFi internet connections, leading to a decrease in internet connectivity.

These two factors are most often responsible for internet ping spikes.

Sometimes, the route that allows data to travel smoothly uses multiple networks.

An example of this is the sending of data from your home network to your internet service provider network, and back to the transit provider.

It is necessary to determine the exact location of these internet ping spikes. This can be done by analyzing the route or medium through which the data traveled from your device to the server. The traceroute tool quickly sends customized ping echo messages along the route to locate all the routers that replied.

Some tools can be used to analyze the network connection or route problems. These tools include WinMTR, PingPlotter and they send traceroutes automatically after every minute to monitor the network for a longer period.

Ping spikes can be described as excessive engagement along the route of the pinging packets.

This happens because too many ping packets or ping spikes are arriving at routers simultaneously, and it causes your package to be delayed or ping to fail.

These reasons can cause ping spikes that are often very frequent:

  • Google Router may experience some inconvenience due to the large number of people who are using the same connection or sharing it with you.
  • This can only happen because of the incorrect software configuration.
  • Hardware failure, etc.

It is, therefore, crucial to identify the source of ping spikes. These steps will help you figure it out:

  • Navigate to navigate “Tracert to Google.com.”
  • Start a “Prompt” command
  • In it, enter the “tracert Google.com” This will send the tracert to Google and make the data travel. As long as the route between you and Google is reasonable, it will only respond to a few pings.
  • Take note of the first and second hops.
  • Start command three and run “ping -n100 x.x.x.x.x.” to reach your router, ISP, and then google. Finally, you can enter the x.x IP address of your router.

How to Troubleshoot Internet Ping Spikes

It could be that your internet connection is trying to find the best network available, causing ping spikes every 30-60 seconds.

Several troubleshooting steps can be taken to remove this reoccurring issue.

In Windows, type “cmd”

When it displays the Settings, enter netsh WLAN. It might also display one option in the network settings.

Wireless Network Connection offers the option to enable the auto-configuration logic via the network interface.

If you see this, type the following: “netsh WLAN setup auto-config enabled with no interface” to trigger the response: “Autoconfiguration disabled for your interface over your Wireless Network Connection.”

If the response doesn’t get activated, it could be due to a typo in your interface ” =” section.

You might find Wireless Network Connection in your Adaptor Settings. There may be 2 or 3.

As mentioned above, these actions can prevent your wireless device from searching nearby internet networks and the updating process of your signal quality. This is why internet ping spikes are unnecessarily occurring out of nowhere.

It is important to turn your actions back on if your Wi-Fi stops searching for nearby networks or if your network goes down.

To do this, copy the previous command and paste it.

netsh WLAN Set auto-config enabled=yes interface=” Wireless Network Connection”

How to Fix Internet Ping Spikes

You will not be able to fix pings if you use the mobile hotspot or Wi-Fi.

These connections can be difficult to repair because they depend on weather conditions and the distance between you, the game server, and the tower.

You cannot fix internet ping spikes if you’re using a mobile hotspot.

If you have a satellite Internet connection with the wireless satellite router, it is possible to make adjustments that will help reduce ping spikes.

  • Navigate to the DSL web report website. The internet connection report will be displayed. Pay attention to buffer bloat. A higher buffer bloat indicates a higher number of ping spikes.
  • With your default router login credentials, log in to your Wi-Fi router.
  • Priority change to enable internet access
  • Your bandwidth can be set to 50-60 seconds of your total bandwidth.
  • You can change the category to the MAC address of the device. This is because you don’t want online applications or games to prioritize your priorities.
  • For a faster ping-less internet connection, set your speed priority to “high”.
  • Finally, you can save your settings.

You will be amazed at what happens when your DSL Report is reopened. You can scan another test by refreshing the DSL Report page.

You will notice a significant improvement in buffer bloat, which is excessive peeing over idle. Your internet spikes will be fixed if your test results are A+.

Categorized in: